RigCheckup

Speaker Test

Play a tone on each channel to check your stereo setup, then run the frequency sweep to test your full hearing range.

Left
Both
Right

Frequency sweep (20 Hz → 20 kHz)

A rising tone across the entire audible range — note where it becomes audible and where it fades out.

20 Hz – 20,000 Hz

Start at a low volume — especially with headphones. The sweep begins with deep bass that can be surprisingly loud on some systems.

Collect all your test results on one sheet: PC Checkup Report

What this test checks

The left/right tone test catches swapped or dead stereo channels. If the "Left" tone comes out of your right speaker, your cables or balance settings are reversed; if one side is silent, check the plug, the balance slider, and the speaker itself in that order.

The frequency sweep plays every pitch from 20 Hz to 20,000 Hz. Most adults stop hearing somewhere between 12–17 kHz — that's normal hearing, not a speaker fault. But if the sound cuts out, crackles, or buzzes in the middle of the sweep, that points to a damaged driver or loose connection.

How this test works

Our speaker test does not play an audio file. It generates sound on the spot using the browser's Web Audio capability. An oscillator produces a pure sine tone at a single frequency, and that signal passes through a StereoPanner stage that routes it to the left channel only, both channels, or the right channel only. When you press the left button, the right channel carries mathematically perfect silence, so any sound from the right speaker is not coming from our signal; the channels are being mixed somewhere further down the chain.

The frequency sweep drives the same oscillator from 20 Hz to 20,000 Hz over eight seconds. It rises exponentially rather than in a straight line because the ear perceives pitch as ratios: the step from 20 Hz to 40 Hz is one octave, and so is the step from 10,000 Hz to 20,000 Hz. An exponential sweep gives every octave the same amount of time, so bass and treble get an equal hearing. A linear sweep would rush through almost all of the bass in the first second, leaving no chance to notice a problem there.

Playing sound does not require a permission prompt the way a microphone or camera does, but browsers refuse to start audio until you have interacted with the page. That is why nothing happens until you click a play button, and on systems with strict autoplay blocking the very first click may pass silently. Because a full-scale tone can be unpleasant or harmful at high volume, we always show a reminder to begin at a low level.

Nothing is recorded or transmitted. The tone is created inside the browser and sent to the operating system's output device; the microphone is never opened. The only thing our server receives is the request for the page.

How to read the results

The left/right tones have three possible outcomes. If the left button sounds only the left speaker and the right button only the right, your setup is correct. If the left tone comes from the right speaker, the channels are swapped: most often the speaker cables are crossed or the two speakers have simply been placed on the wrong sides, though some audio utilities also offer a channel-swap option that may have been switched on. If one button produces silence, the fault lies in that channel's connection, the balance setting, or the speaker unit itself. If both buttons play from both sides, your output is being summed to mono; check the mono audio option in accessibility settings or a mono mode on a Bluetooth device.

The point at which the sweep seems to vanish is far more likely to be your own hearing limit than a speaker fault. Sensitivity to high frequencies declines naturally with age, and many adults stop hearing somewhere between about 12 and 17 kHz. Silence in that region is not a defect. The easy way to tell the difference is to play the sweep for someone else or on different speakers and see whether it fades at the same point.

Problems that appear in the middle of the sweep, by contrast, are equipment signals. A rattle or buzz that occurs only around a particular frequency usually means something is resonating: a loose screw or grille on the enclosure, or an object on the desk vibrating in sympathy. A dropout, a tearing sound or crackle confined to one region can indicate a damaged driver or a poor connection. Noting roughly how far into the eight seconds the problem occurs gives you a useful idea of the frequency involved when you look for a fix or describe the fault for repair.

The first second or two of the sweep, from 20 Hz to around 60 Hz, is subwoofer territory. Laptop speakers and small Bluetooth speakers physically cannot reproduce it, so silence at the very start is normal for them. On a 2.1 system or a pair of full-size speakers you should feel a low rumble there; if you do not, check the subwoofer's power, cable and crossover setting.

When to use it: common situations

The classic use is right after connecting new speakers or headphones. The left/right tones confirm the wiring in seconds, and they catch the easy mistake of placing the left speaker on the right side of the desk. The same quick check applies after re-plugging a 3.5 mm cable, an optical cable, or the speaker terminals on the back of an amplifier.

When sound goes wrong after an operating-system update or a driver change, the test helps split the problem. If both channels sound clean here, the hardware and the system output path are fine and the trouble lies inside a particular application. If one side is missing or crackling here too, look at the system output device, balance, driver, or the hardware itself.

With Bluetooth headsets and speakers you can check channel separation and quality at the same time. In the call profile most devices collapse to mono and lose their top end, so if both buttons play from both sides or the sweep fades unusually early, the device may be stuck in call mode. Close every application that uses the microphone and run the test again; the difference is usually obvious.

If you suspect a speaker or headphone is damaged and are weighing a return or repair, the sweep gives you evidence. A tearing sound that repeats at the same frequency every time, while another output device plays that region cleanly, points to a damaged driver and is easy to describe to the retailer or service centre. Running this check on second-hand speakers or headphones inside the return window is well worth the minute it takes.

Limits of a browser test and what to check elsewhere

The loudness of what the browser plays passes through the operating system's volume mixer and output settings. We send the signal at a modest level, but the final volume is set by the system volume, any per-application volume, and the dial on your amplifier or speakers, so always begin with the system volume turned down. Equalisers, spatial audio and loudness compensation applied by the operating system can also change how the sweep sounds, and our page has no way of knowing whether any of them is switched on.

This is a listening tool, not a measurement instrument. It tells you whether sound comes out, which side it comes from, and where something sounds wrong; it cannot plot a frequency-response curve, measure distortion, or quantify a level difference between channels. That requires a measurement microphone and dedicated software. The point where the sweep fades is also inherently ambiguous, because the limit of the speaker and the limit of your hearing overlap there, and the test alone cannot separate them. Comparing with another listener or another output device is the simplest way to resolve it.

If an application holds the output device in exclusive mode, browser audio may not play at all, and if the operating system has chosen an unexpected default output such as a monitor's HDMI audio, a perfectly good pair of speakers will seem silent. The browser does not display which device it is sending sound to, so when you hear nothing, the first thing to check is the currently selected device in the system output list.

For one silent side or swapped channels, the speaker one-side guide walks through plug, balance, cable and mono settings in order. For crackle, buzz or dropouts heard during the sweep, the speaker crackling and noise guide explains how to tell a loose connection, power interference and a damaged driver apart. Both guides are written to start from the symptom you have just observed here.

Frequently asked questions

I pressed play and hear nothing.
Check the system volume and mute first, then whether the browser tab itself is muted. Next, make sure the operating system's output device is the speaker or headphones you are actually listening to — a monitor's built-in speakers or a disconnected Bluetooth device being selected is extremely common. If video sound works on other sites but this tone does not, reload the page and press play again.
The left tone plays from both sides.
If the operating system's mono audio accessibility option is on, left and right are merged and both sides play the same sound. The same happens with physically mono devices such as a single Bluetooth speaker or a phone speaker. Virtual surround and spatial audio features in some sound drivers can also blur channel separation, so turn them off and test again.
I cannot hear the end of the frequency sweep. Is it the speakers?
Usually not. High-frequency hearing declines with age, and most adults stop hearing somewhere between 12 and 17 kHz. Having another person listen, or trying another device, will tell you which it is. If instead a band in the middle of the sweep drops out or rattles, that may point to a problem with the driver or the enclosure.
The beginning of the sweep is silent.
Laptop speakers, small Bluetooth speakers and most earbuds physically cannot reproduce the very low bass between 20 and 60 Hz. That is a limit of driver size, not a fault. If you have a subwoofer, this part of the sweep is a handy way to confirm it is working. Do not turn the volume up because you hear nothing — the midrange that follows will suddenly be loud.
How loud should I set the volume for testing?
Start at half your normal listening level or lower. A pure sine tone sounds much louder than music at the same setting, and the 2–5 kHz range is where the ear is most sensitive. Always begin at low volume with headphones or earbuds, and press stop immediately if it becomes uncomfortable.

Related guides